Skip to content

Home
About
Membership
Meetings
Gallery
- Member’s Work
- Meeting Photos
Outreach
- Ventura County Fair
- Cabrillo Middle School
Learn to Turn
Contact

October 2018 – Michael Mocho

ByRon Lindsay October 29, 2018October 11, 2024

Business meeting

Several members of the Glendale club attended including VP Kim A.

Our demonstrator for today is Michael Mocho from Albuquerque.

Two-minute egg cut with his favorite tool, the skew

Michael started off showing examples of texturing

Some are cuts and some are compressions

Spiral to a point

Boxes. The spirals are added as inserts.

A free ring on a socketed finial.

A threaed box. The three sides were formed by sanding.

Ball and socket joints. He did not demonstrate today how the joints are done.

Preparing a blank in Maple.

The skew as an end grain cutter

Chatter work done with the big skew.

Different angles of presentation give different effects

Like so

The skew or angled scraper can also cut coves as well as beads

Cut a dimple to center the drill.

Since is hard to push straight, take short strokes when honing skew.

Sizing the handle dowel with metal drill gauge pushed on by tailstock quill

Steel drill gauge

Finished top textured on both top and bottom

Note diameter cAliper at center top

Michael presented history of lathe and a wide selection of his turning work

Wooden ribbons and boxes

Horn for speaker system

Arnie J. get lesson on handling the skew. Toolrest height and body stance are important.

Beads, coves and free rings with the skew

Cuttng coves with heavy duty angled scraper

Fish hook diamond sharpener useful on gouges

The Sorby large spiraling texture tool. Cuts on the top corner

Cutting the spiral to a point

Example of knurling tool which compresses the woood

First get tool spinning, then angle down to catch the top edge to cut the spiral

Different effects with this tool combined

Sandpaper wrapped around a slotted dowel will polish the straight insides.

An insert for the inside bottom.

Chasing a male thread. He uses dish detergent to lubricate the Maple wood surface.

Some chasers come with a half tooth which must be ground off.

Two-page handout of Michael’s words of wisdom.

Workshop with Michael Mocho – Al G.

Kirby K., Darrel Wilson

Joe S., Kirby K.

Sam T., Michael Mocho, Joe S, Kirby K.

Sam T., Michael Mocho, X, Joe S.

David F. and Darrel W.

Post navigation

September 2018 – Paulo Marin Tools

November 2018 – Lyle Jamieson – Webinar

Similar Posts

February, 2009
Bynstryker@gmail.com February 1, 2009October 11, 2024

President’s Corner – Steve Leblanc Gallery event The AAW is encouraging local chapters to host a gallery event. I received a letter from Frank Amigo of the AAW board, and I want to present this suggestion to the general membership and see if there is any interest in doing this. I have been personally involved…

Read More February, 2009
January, 2004
Bynstryker@gmail.com December 1, 2004October 11, 2024

Meeting Information: Saturday, January 24 from 9:00 am to Noon Hands-on Workshop with emphasis on tools and sharpening at Russ Babbitt’s: The first meeting of the year will start us off with a teaching session for new, beginning, and advanced turners to share ideas, techniques, and mistakes we have made or will make. Four lathes…

Read More January, 2004
January 2020 – Joanne Sauvageau
ByRon Lindsay January 25, 2020October 11, 2024

Read More January 2020 – Joanne Sauvageau
August 2015 Hands-On
ByRon Lindsay August 31, 2015October 11, 2024

Read More August 2015 Hands-On
November 2018 – Lyle Jamieson – Webinar
ByRon Lindsay November 17, 2018October 11, 2024

Read More November 2018 – Lyle Jamieson – Webinar
July 2016 – Summer Party
ByRon Lindsay July 23, 2016October 11, 2024

Read More July 2016 – Summer Party

Channel Islands Woodturners is a 501(c)3 nonprofit
© 2026 Channel Islands Woodturners

Home
About
Membership
Meetings
Gallery
- Member’s Work
- Meeting Photos
Outreach
- Ventura County Fair
- Cabrillo Middle School
Learn to Turn
Contact