Skip to content

Home
About
Membership
Meetings
Gallery
- Member’s Work
- Meeting Photos
Outreach
- Ventura County Fair
- Cabrillo Middle School
Learn to Turn
Contact

June 2019 – Hans Weissflog

ByRon Lindsay June 17, 2019October 11, 2024

Al G. introducing Hans Weissflog from Germany

A sampling of Hans’ work

Each side is single block of wood

Standing Oval Box

Standing Oval Box

Demonstrator Hans Weissflog will do three projects – detailed plans are available on our website under Members tab

First project is lattice-top lidded box – custom chuck

Showing shape of custom scraper 0.9 mm wide

Custom scraper for cutting grooves

Find the center hole of offset disk with pin

Cut grooves to shallow uniform depth – extend lattice to entire top surface

Flip over, hollow, and cut lattice through to opposing side

Cut through just enough to reveal opposite lattice

Sand and clean out the lattices – the tedious part

Preparing a jam chuck

Cut off the temporary tenon

Clean up the bottom using jam chuck

Finished lattice-top box

Second project is Standing Oval Box – Form 60 mm spherical shape

Use template to assure correct shape

Create jam chuck to hold spherical blank – note the inverted gouge useful when hollowing end grain

Blank in jam chuck

Hollow out according to the plan

Here is where we are going

Now the top in contrasting wood – prepare the tenon and reverse

Cut the mating surface

Use template to assure correct shape

Reverse on jam chuck

and shape to match spherical template

Now we have a spherical box – next flatten to oval shape

Place in jam chuck to hold the sphere – rotated 90 deg

Cut down to predetermined depth

Cut down to shape of oval template

Flatten bottom using jam chuck

Third and final project is Drunken Box or Twisted Cone – Make a spherical box, rotate 90 deg, and cut cone on opposing sides

Cut hemisphere and check with template

Prepare opposite half

Cut cone to exact marks – must be exactly square

Flip over – but how to hold?

Hans made a purpose-made compression chuck

Cut the opposite side cone

Rotate the halves 90 deg to form the drunken shape

Drunken Box

Hans concluded demo with 45 min slide show of his and son’s work

Masur Birch and Blackwood Standing Oval Box

Other twisted shapes

Lots of African Blackwood, Cocobolo, Masur Birch, and Boxwood

Cocobolo

His giant stash of Blackwood

Son Jakob Weissflog

Some of Jakob’s work

More …

And more

Post navigation

May 2019 – Stabilizing Wood

July 2019 – Summer Party

Similar Posts

January, 2004
Bynstryker@gmail.com December 1, 2004October 11, 2024

Meeting Information: Saturday, January 24 from 9:00 am to Noon Hands-on Workshop with emphasis on tools and sharpening at Russ Babbitt’s: The first meeting of the year will start us off with a teaching session for new, beginning, and advanced turners to share ideas, techniques, and mistakes we have made or will make. Four lathes…

Read More January, 2004
November, 2004
Bynstryker@gmail.com December 1, 2004October 11, 2024

Meeting Information: Sunday, November 7, from 8 am to 4 pm Soren Berger: Special Demo Reservations required see below! Also note the early start times! At Levi Mize Woodcraftsman’s Shop 162 Aviador Street #17+18, Camarillo, CA 93010 Aviador Street is N. of the Camarillo Airport and is reached from the Central Ave. exit off of…

Read More November, 2004
August 2013 – VC Fair
ByRon Lindsay August 1, 2013October 11, 2024

Read More August 2013 – VC Fair
October 2015 – John Wells
ByRon Lindsay October 24, 2015October 11, 2024

Read More October 2015 – John Wells
July 2018 – Summer Party
ByRon Lindsay August 9, 2018October 11, 2024

Read More July 2018 – Summer Party
October 2022 Meeting
ByRon Lindsay October 23, 2022October 11, 2024

Read More October 2022 Meeting

Channel Islands Woodturners is a 501(c)3 nonprofit
© 2026 Channel Islands Woodturners

Home
About
Membership
Meetings
Gallery
- Member’s Work
- Meeting Photos
Outreach
- Ventura County Fair
- Cabrillo Middle School
Learn to Turn
Contact